Posts by dskagcommunity

21) Message boards : Number crunching : 7950 GPU core low frequency while crunching WUs (Message 58123) Posted 4 May 2013 by dskagcommunity Post: So, i have some News for the threadstarter. I got nearly this issue on Einstein@home Project. After reading a little bit on internet about 7950 boost i found out that this card downclocks to 850mhz when it means to max the TDP. You can prefend this by two ways. Either you set the Power Limit Adjustment in CCC or Afterburner to +20% or you upload a new standart non boost bios into the card. I choose to set it absolut manual over afterburner @ 900Mhz, with 1,075 voltage for cooler running (it showed up 1,175!) after activading the stable voltage control in afterburner settings!, 45% GPU Fan (so it runs with 51degress now) and +20% PowerLimit. It seems stable at the moment. For safety i dont run it at the full boost speed, dont want to ruin the card in garantueetime with 24/7 powerclocking on full load ^^ perhaps i downclock it a littlebit to 880 or something that would be between boost and nonboost mode. The main!problem i saw with this coreclockchange from ATI is a massive performancereduction. It goes down every second from 94 to 60% GPU Load and up again and down and up! Some say we should RMA our cards (because while gaming it could bring too problems with this clockchanges and the lower performance), but i dont want to because it is a dedicated crunching and no gamingmachine. Hope i could help ya.
22) Message boards : News : Separation Runs ps_p_82_1s_dr8_4 and de_p_82_1s_dr8_4 Started (Message 57992) Posted 24 Apr 2013 by dskagcommunity Post: I have too a problem on hd 4850 with this series of wus.
23) Message boards : Number crunching : 7950 GPU core low frequency while crunching WUs (Message 57899) Posted 12 Apr 2013 by dskagcommunity Post: I see that you are using an actual beta driver. Often new drivers arenÂ´t optimized for GPU-computing, but for gaming. IÂ´m using Catalyst 12.7 for crunching milkyway on my two 7950 (core clock 900 MHZ) without problems. Any newer drivers performed weaker for me. Maybe you try a rollback to an older driver Nowi Yep i using too an "older " driver always. I think ive running cat 12.6 or .8
24) Message boards : Number crunching : 7950 GPU core low frequency while crunching WUs (Message 57834) Posted 7 Apr 2013 by dskagcommunity Post: I too can only say on my 7950 i was running one WU at once with 64secs per. i think it showed all the time 950?Mhz (Boost edition) when i remember right.
25) Message boards : Cafe MilkyWay : Milestones IV (Message 56699) Posted 3 Jan 2013 by dskagcommunity Post: dancing Finally on 20M! A happy new Year Milestone ^^
26) Message boards : Cafe MilkyWay : Team Recruitment III (Message 56685) Posted 1 Jan 2013 by dskagcommunity Post: We from "DSKAG Austria" Research Team searching for more Members from Austria who nearly only compute for Medical or Astronomical Researches (including POEM of course ;)). So plz no Math Guys :) Let others show that Austria is not that small as it is, and is able to find solutions for much diseases :)
27) Message boards : Number crunching : Mis-reading my hardware? (Message 56577) Posted 20 Dec 2012 by dskagcommunity Post: Driver or boinc updated??
28) Message boards : Number crunching : Nvidia Geforce GTX 650 Ti slower than GTX 285 ? (Message 56497) Posted 14 Dec 2012 by dskagcommunity Post: 6xx cards has a horrible DP Performance to get user to buy there tesla cards..
29) Message boards : News : validator back up (Message 56439) Posted 9 Dec 2012 by dskagcommunity Post: Hm i have nearly 300 wus without validating including a wingman finished too but not resend to a third one :( and it raising hard :/
30) Message boards : Number crunching : Validator stopped. (Message 56411) Posted 6 Dec 2012 by dskagcommunity Post: Dont know what sense it has to move to other projects..nothing is lost due validator stop ^^
31) Message boards : Number crunching : Validator stopped. (Message 56406) Posted 6 Dec 2012 by dskagcommunity Post: Hope it get turned on before the database explods ;) 721000 results waiting ^^
32) Message boards : Number crunching : Crunch with Ati 4870 & 6870 in the same computer (Message 56397) Posted 5 Dec 2012 by dskagcommunity Post: Plz write down your result if you bring it to work. I will face this problem in i think 2 months too with a 4850 and a 7950. ^^
33) Message boards : Number crunching : Validator stopped. (Message 56394) Posted 5 Dec 2012 by dskagcommunity Post: Seems there is a problem with the validator. The service seems to stopped one or two hours ago.
34) Message boards : Number crunching : app_info file for Gigabyte Radeon HD 7950 GPU (Message 56331) Posted 30 Nov 2012 by dskagcommunity Post: Thanks for the info. It's working great and crunching away! Out of curiosity what makes an app_info file so desirable? I started with 1 WU/min and now with the file I'm doing 2 Wu's/2 mins. Your right on some single projects it makes not really big sense. I calculated a few 1000 points more on a 7950 but...it gives over 300k so some 1000 are not important (for me) ^^
35) Message boards : Number crunching : GPU usage (Message 56159) Posted 11 Nov 2012 by dskagcommunity Post: I think it has more sense to run them on poem :)
36) Message boards : Cafe MilkyWay : Milestones III (Message 56144) Posted 9 Nov 2012 by dskagcommunity Post: 15M!!!!!!!!!!!!!!!!!!!! raveing :P ^^
37) Message boards : News : Updated max errors to 2 (Message 56066) Posted 3 Nov 2012 by dskagcommunity Post: I have too two Workunits that are finished but cant validate :/
38) Message boards : News : New(er) Searches (Message 56065) Posted 3 Nov 2012 by dskagcommunity Post: have summary yesterday and today only 4 computing errors, so it seems to go back to normal business soon for me ^^ Oh yes, and good desition to go to double up the cumputing time per WU :)
39) Message boards : Number crunching : Lots of crunching errors since today (Message 55940) Posted 24 Oct 2012 by dskagcommunity Post: Yes lets hope they soon through. I have around 7-20 error units per days at the time.
40) Message boards : News : Apology for recent bad batches of workunits (Message 55828) Posted 16 Oct 2012 by dskagcommunity Post: Your right i have errors too until today.

Previous 20 · Next 20