Welcome to MilkyWay@home

New Benchmark Thread - times wanted for any hardware, CPU or GPU, old or new!

Message boards : Number crunching : New Benchmark Thread - times wanted for any hardware, CPU or GPU, old or new!
Message board moderation

To post messages, you must log in.

1 · 2 · 3 · 4 . . . 19 · Next

AuthorMessage
[TA]Assimilator1
Avatar

Send message
Joined: 22 Jan 11
Posts: 375
Credit: 64,657,871
RAC: 0
Message 61794 - Posted: 28 May 2014, 20:35:43 UTC
Last modified: 28 May 2014, 20:49:16 UTC

I know lots of people running MW@H like to know how their rigs compare to other peoples & would like to see how an upgrade would improve output.
Whilst you can look through the MW BOINC stats the info is rather vague, it doesn't give clock speeds or specific GPUs for example, nor does it account for anything that might add to WU times.

So please share your new scores for old & new GPUs & CPUs alike!

Please note new requirements for the benchmark :-

Validated 106.88 credit WUs only & must be from the MilkyWay@Home v1.02 app*.

Average of 5 WU times
(not cherry picked please! ;) ).

A dedicated CPU core for each GPU, please state clock speeds if overclocked (including factory overclocks) or state 'stock'.

Please only crunch 1 WU at a time per GPU otherwise it will massively increase WU time! (even if it does increase output, the WU times seem to fluctuate much more than singly crunched WUs so you can't 1/2 the time either).

For CPUs you'll want to crunch 1 WU per real core.

It would also be handy if you could state your BOINC & driver version & OS, incase it does make any odds.

* the separation mod fit ones are slower. ~20s on my HD 5850 @850 MHz.

Please check in the latest posted benchmark table to see if their are any updates to the benchmark requirements.

*****************************************************************************

If your wondering why I'm starting over again it's because the original (long) version of the 213.76 credit WU used for the benchmark has become only sporadically available now.
At 1st a short version joined it & so for a while we had both (which confused some people) & then the long 1 disappeared altogether for a time! It is sporadically back now but it just makes things too difficult.

Also I later found out that some people don't run the mod fit WUs (like the 213.76s) because of lower credit & some people can't run them due to hardware limitations (e.g HD 3800s). I did ask originally but no one said anything :P.
So this time I've chosen MW v1.02 106.88 credit WU for the benchmark, although it's shorter run times give the illusion of smaller performance gaps between different hardware it'll be easier overall.

Because the rubbish forum software won't allow editing after 1hr I will have to post the latest table towards the end of the thread, or alternately you can check out the table in the AnandTech forum benchmark thread I've created. http://forums.anandtech.com/showthread.php?t=2384985 (which I can update!).

I'll start off with my main rigs time for now :).

Current GPU statistics ~ Average Run Time to Complete 1 106.88 credit WU :-

HD 5850 (GPU 850 MHz, RAM u/c 500 MHz) ............. 51s Assimilator1
HD 5850 (stock, GPU 725 MHz, RAM 1000 MHz) ........ 60s Assimilator1
Team AnandTech - SETI@H, DPAD, F@H, MW@H, A@H, LHC, POGS, R@H, Einstein@H, DHEP, WCG

Main rig - Ryzen 5 3600, MSI B450 G.Pro C. AC, RTX 3060Ti 8GB, 32GB DDR4 3200, Win 10 64bit
2nd rig - i7 4930k @4.1 GHz, HD 7870 XT 3GB(DS), 16GB DDR3 1866, Win7
ID: 61794 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
[TA]Assimilator1
Avatar

Send message
Joined: 22 Jan 11
Posts: 375
Credit: 64,657,871
RAC: 0
Message 61795 - Posted: 28 May 2014, 22:15:24 UTC

Doh! forgot to make AT thread clickable http://forums.anandtech.com/showthread.php?t=2384985
Team AnandTech - SETI@H, DPAD, F@H, MW@H, A@H, LHC, POGS, R@H, Einstein@H, DHEP, WCG

Main rig - Ryzen 5 3600, MSI B450 G.Pro C. AC, RTX 3060Ti 8GB, 32GB DDR4 3200, Win 10 64bit
2nd rig - i7 4930k @4.1 GHz, HD 7870 XT 3GB(DS), 16GB DDR3 1866, Win7
ID: 61795 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
Tom*

Send message
Joined: 4 Oct 11
Posts: 38
Credit: 309,729,457
RAC: 0
Message 61796 - Posted: 28 May 2014, 22:36:07 UTC
Last modified: 28 May 2014, 22:51:43 UTC

HD7950 oc at 1100 but drops to 900 during run, jumps between 1100 and 900.

AMD A8 at 3.4 Default. Win 7 64 bit

ave time is 33.06 seconds but when 4 CPU's are running T4T times go up to 35 and 36 seconds.

http://milkyway.cs.rpi.edu/milkyway/results.php?hostid=509400&offset=0&show_names=0&state=0&appid=3

Catalyst old 13.2 beta 7 moded with OpenCL 12.4 due to bad OpenCL compiler released on 13.1 which was latest when I installed the HD7950.

They must have fixed the bad compiler but it was still bad in early 13.x versions.
ID: 61796 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
S@NL - JBG

Send message
Joined: 4 Mar 10
Posts: 6
Credit: 1,057,111
RAC: 0
Message 61798 - Posted: 29 May 2014, 1:18:40 UTC
Last modified: 29 May 2014, 1:21:06 UTC

The results with the request test setup:

<app_config>
<app>
<name>milkyway</name>
<gpu_versions>
<gpu_usage>1</gpu_usage>
<cpu_usage>1</cpu_usage>
</gpu_versions>
</app>
</app_config>


Temperature / GPU = 66 Celcius by 100% usage
Did crunched 1 WU / GPU with 1 CPU / GPU
The GeForce GTX 690 has 2 GPUs on board

Here the last 5 best results:

753950984 563958930 547777 395.38 3.68 106.88 MilkyWay@Home v1.02 (opencl_nvidia)
753950983 563958929 547777 393.19 4.06 106.88 MilkyWay@Home v1.02 (opencl_nvidia)
753950962 563958908 547777 393.37 3.65 106.88 MilkyWay@Home v1.02 (opencl_nvidia)
753685445 563764367 547777 394.19 3.63 106.88 MilkyWay@Home v1.02 (opencl_nvidia)
753681312 563761206 547777 393.18 3.92 106.88 MilkyWay@Home v1.02 (opencl_nvidia)

The average time for crunching is now ~394sec / WU
Link: http://milkyway.cs.rpi.edu/milkyway/results.php?userid=91948&offset=0&show_names=0&state=0&appid=3
ID: 61798 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
[TA]Assimilator1
Avatar

Send message
Joined: 22 Jan 11
Posts: 375
Credit: 64,657,871
RAC: 0
Message 61801 - Posted: 29 May 2014, 18:31:16 UTC
Last modified: 29 May 2014, 19:27:19 UTC

Thx for your times guys :)

JBG
Yep I can certainly add those :).
Stock clocks right?

Btw, from old thread :-

go do your test next time a bit longer, so that you can do a much better average time calculation

What on earth do you mean by that? lol. I didn't post any times in my last post there...
Nice jump in your credits btw :).

Tom
I don't quite understand why your GPUs clock speed is jumping around, is it overheating? If so then you ought to either boost fan speed or drop the clock rate. Anyway I'm afraid I can't use an average taken from such large jumps in clock speed, it needs to be at a steady speed to give a meaningful benchmark.
Drop us your times when you've fixed it :).

Incidentally Cat 13.1 works fine with MW@H, that's what I & many others use.
Without moding, latter ones don't seem to work with HD 5800s & 6900s on MW.

******************************************************************************

Current GPU statistics ~ Average Run Time to Complete 1 MW v1.02 106.88 credit WU :-

HD 7950 (GPU 1,188 MHz, RAM 1,250 MHz) ............ 24.1s ... GLeeM
HD 7950 (GPU 1,000 MHz, RAM 1,250 MHz) ............ 28.1s ... GLeeM
HD 79?? (stock) .................................................. 39.8s ... Rudy Toody
HD 5850 (GPU 850 MHz, RAM u/c 500 MHz) ............ 51s ... Assimilator1
HD 5850 (stock) .................................................. 60s ... Assimilator1
GTX 690 (stock?) ............................................... 394s ... S@NL - JBG (dual GPU card)

As before, the links are busted due to this forums software, go to the AnandTech thread if you want to check out the links.
Team AnandTech - SETI@H, DPAD, F@H, MW@H, A@H, LHC, POGS, R@H, Einstein@H, DHEP, WCG

Main rig - Ryzen 5 3600, MSI B450 G.Pro C. AC, RTX 3060Ti 8GB, 32GB DDR4 3200, Win 10 64bit
2nd rig - i7 4930k @4.1 GHz, HD 7870 XT 3GB(DS), 16GB DDR3 1866, Win7
ID: 61801 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
S@NL - JBG

Send message
Joined: 4 Mar 10
Posts: 6
Credit: 1,057,111
RAC: 0
Message 61803 - Posted: 29 May 2014, 21:35:47 UTC - in response to Message 61801.  
Last modified: 29 May 2014, 21:43:32 UTC

@Assimilator1:

Yes the Card = in Stock values

Info from CUDA-Z:
Clock Rate: @1019,5Mhz with driver v332.21
MultiProcessors: 8 (1536 Cores)
Memory per GPU: 2048 MiB / 256bits / Clock Rate: 3004MHz
Performance:
Single-precision Float: 1925.06 Gflop/s
Double-precision Float: 138.656 Gflop/s

Also iam using always the programm TThrottle to keep the temperature below 76 degr.C

About the times in my list for v1.02...
only the times between 393 and 442 sec are crunched with the 1NV / 1CPU setup (1 WU / GPU)

the times from arround 500sec are WUs that been started with the 0,25NV setup,
and ended with the 1NV setup.. so you can just forget those..
and the times arround 700+ sec are done with the 0,25NV setup (4WUs / GPU),
you also can fotget those..

hope that you now understand the jumping in seconds between results.. ?
ID: 61803 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
[TA]Assimilator1
Avatar

Send message
Joined: 22 Jan 11
Posts: 375
Credit: 64,657,871
RAC: 0
Message 61804 - Posted: 29 May 2014, 22:02:29 UTC - in response to Message 61803.  

Yea no probs with your times, it was Toms times that I couldn't use.
Although are you saying your throttling your GPUs? That would hurt times!
Btw I believe 76C is a long way below their safe max.

I guess you missed his name in my post ;).
Team AnandTech - SETI@H, DPAD, F@H, MW@H, A@H, LHC, POGS, R@H, Einstein@H, DHEP, WCG

Main rig - Ryzen 5 3600, MSI B450 G.Pro C. AC, RTX 3060Ti 8GB, 32GB DDR4 3200, Win 10 64bit
2nd rig - i7 4930k @4.1 GHz, HD 7870 XT 3GB(DS), 16GB DDR3 1866, Win7
ID: 61804 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
DutchDK

Send message
Joined: 13 Nov 10
Posts: 5
Credit: 18,929,782
RAC: 0
Message 61805 - Posted: 29 May 2014, 22:44:00 UTC
Last modified: 29 May 2014, 22:51:38 UTC

Benching mode enabled :
App_config.xml amended to enable only 1 GPU and 1 CPU per WU. HT disabled in bios.
Configuration :
Dual Xeon X5570 CPU, Asus Z8PE-D12X MB, 48 GB DDR3 1333 Mhz ECC ram, 1 Sapphire Vapour-X R9-280X Tri-X OC edition card (factory OC to 1100 Mhz Core/1500 Mhz Mem) running at 1185 Mhz Core/1600 mhz Mem, 1 Asus Radeon DCII-TOP R9-280X card (factory OC to 1070 Mhz Core/1600 Mem) running at 1185 Mhz Core/1600 mhz Mem.
Windows 7 64bit, Boinc 7.2.42(x64), Catalyst 14.4

Times swinging between 23.03 secs and 23.10 secs.
Average time selected in bench of 5 units : 23.04 secs
WUtask WU Computer DateStart DateReported Status Runtime CPUtime Credit Application
754764484 564551494 561358 29 May 2014, 22:01:06 UTC 29 May 2014, 22:33:57 UTC Completed and validated 23.04 1.84 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
754764482 564551491 561358 29 May 2014, 22:01:06 UTC 29 May 2014, 22:33:57 UTC Completed and validated 23.03 1.78 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
754763115 564572517 561358 29 May 2014, 21:58:52 UTC 29 May 2014, 22:31:43 UTC Completed and validated 23.04 1.76 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
754763112 564572514 561358 29 May 2014, 21:58:52 UTC 29 May 2014, 22:31:43 UTC Completed and validated 23.04 1.70 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
754762465 564572038 561358 29 May 2014, 21:57:44 UTC 29 May 2014, 22:29:30 UTC Completed and validated 23.04 1.90 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)

CPU Xeon X5570 2.93 Ghz Quadcore with Turbo boost up to 3.33 Ghz, normally running Turbo boost at 3.20 Ghz during a Boinc run.
Average per WU : 3,376.028 seconds (56 minutes, 16.028 seconds)

WUtask WU Computer DateStart DateReported Status Runtime CPUtime Credit Application
754730787 564547726 561358 29 May 2014, 21:03:36 UTC 29 May 2014, 22:28:23 UTC Completed and validated 3,381.49 3,364.40 106.88 MilkyWay@Home v1.00
754730176 564547237 561358 29 May 2014, 21:02:29 UTC 29 May 2014, 22:27:16 UTC Completed and validated 3,377.42 3,360.26 106.88 MilkyWay@Home v1.00
754730175 564547236 561358 29 May 2014, 21:02:29 UTC 29 May 2014, 22:27:16 UTC Completed and validated 3,378.44 3,361.87 106.88 MilkyWay@Home v1.00
754730173 564547234 561358 29 May 2014, 21:02:29 UTC 29 May 2014, 22:27:16 UTC Completed and validated 3,365.37 3,348.06 106.88 MilkyWay@Home v1.00
754730148 564547209 561358 29 May 2014, 21:02:29 UTC 29 May 2014, 22:27:16 UTC Completed and validated 3,377.42 3,360.56 106.88 MilkyWay@Home v1.00
ID: 61805 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
Tom*

Send message
Joined: 4 Oct 11
Posts: 38
Credit: 309,729,457
RAC: 0
Message 61806 - Posted: 30 May 2014, 15:03:11 UTC - in response to Message 61796.  
Last modified: 30 May 2014, 15:57:57 UTC

With the HD7950 clock set to 900 no variation occurs and the timings are very similar 33.05 seconds average .01 sec variance with No CPU jobs.

Its not heat that varies the clock when set to 1112 oc via MSI afterburner
as Einstein and SETI do not vary.
ID: 61806 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
superpower

Send message
Joined: 30 Aug 10
Posts: 10
Credit: 22,660,541
RAC: 0
Message 61807 - Posted: 30 May 2014, 17:50:40 UTC

My system spec:

CPU Intel Core i7 CPU X 980 @ 3.33GHz
SAPPHIRE HD 5970 (OC Edition) (gpu clock 735 and memory clock 1010)
Catalyst version 12.6
Windows 7 Ultimate x64 Edition
BOINC version 7.0.64
The HD 5970 is a dual-gpu card and I have a 100% gpu utilization with 1 WU/Core.

Gpu stock

755439374 565085656 30 May 2014, 17:06:20 UTC 30 May 2014, 17:32:51 UTC Completed and validated 52.35 1.78 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
755439373 565085655 30 May 2014, 17:06:20 UTC 30 May 2014, 17:32:51 UTC Completed and validated 53.12 1.95 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
755439372 565085654 30 May 2014, 17:06:20 UTC 30 May 2014, 17:32:51 UTC Completed and validated 52.21 1.73 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
755439367 565085649 30 May 2014, 17:06:20 UTC 30 May 2014, 17:21:47 UTC Completed and validated 53.21 1.79 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
755439363 565085645 30 May 2014, 17:06:20 UTC 30 May 2014, 17:32:51 UTC Completed and validated 52.22 1.64 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
ID: 61807 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
[TA]Assimilator1
Avatar

Send message
Joined: 22 Jan 11
Posts: 375
Credit: 64,657,871
RAC: 0
Message 61808 - Posted: 30 May 2014, 18:08:43 UTC - in response to Message 61806.  
Last modified: 30 May 2014, 19:08:30 UTC

Thx for the times folks :)

Btw does anyone know another English capable speaking Team whose forum & MW team is very active? (so I can gather more times).
Didn't try SETI.USA before because their MW forum looked dead, but looking at the views/replies for the Pentathlon thread maybe I was wrong, so I'm going to try them.

Tom
Ah ok, is it hitting a power tune limit then? Btw the MW v1.02 WUs draw a lot more power than the mod fit WUs, does the speed vary for them too?
Will add the 900 MHz time anyway.

********************************************************************************************************************

Current GPU statistics ~ Average Run Time to Complete 1 MW v1.02 106.88 credit WU :-

R9 280X (GPU 1185 MHz, RAM 1600 MHz) .............. 23s ...... DutchDK
HD 7950 (GPU 1188 MHz, RAM 1250 MHz) .............. 24.1s ... GLeeM
HD 7950 (GPU 1000 MHz, RAM 1250 MHz) .............. 28.1s ... GLeeM
HD 7950 (GPU 900 MHz) ...................................... 33s ...... Tom*
HD 7950 (stock) .................................................. 39.8s ... Rudy Toody
HD 5850 (GPU 850 MHz, RAM u/c 500 MHz) ............ 51s ..... Assimilator1
HD 5970 (GPU 735 MHz, RAM 1010) ...................... 52.6s ... superpower (dual GPU card)
HD 5850 (stock) .................................................. 60s ..... Assimilator1
GTX 690 (stock) ................................................. 394s .... S@NL - JBG (dual GPU card)

Current CPU statistics ~ Average CPU Time to Complete 1 MW v1.02 106.88 credit WU :-

Intel Xeon X5570 (Turboing to 3.2 GHz) ............... 3376s ... DutchDK

Stock clocks for the above o/ced graphic cards (GPU/RAM MHz):-

HD 5850 ...................... 725/1000
HD 5970 ...................... 725/1000 (dual GPU)
HD 7950 ...................... 800/1250
HD 7950 Boost ............. 850-925/1250
R9 280X ...................... 850-1000/1500
Team AnandTech - SETI@H, DPAD, F@H, MW@H, A@H, LHC, POGS, R@H, Einstein@H, DHEP, WCG

Main rig - Ryzen 5 3600, MSI B450 G.Pro C. AC, RTX 3060Ti 8GB, 32GB DDR4 3200, Win 10 64bit
2nd rig - i7 4930k @4.1 GHz, HD 7870 XT 3GB(DS), 16GB DDR3 1866, Win7
ID: 61808 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
WES

Send message
Joined: 22 Feb 14
Posts: 10
Credit: 198,555
RAC: 0
Message 61811 - Posted: 31 May 2014, 14:08:04 UTC

Happy to see a new benchmark started, since I had to replace the card used in the previous test because one of the two fans seized. So I replaced the 7950 TOP with an R9 280X TOP (ASUS). It has a factory OC of 1070Mhz and 1600Mhz on the memory. I use the latest Boinc version and AMD graphics driver (not the beta) on Win7 64bit Pro. Run times to complete "106.88 credit WU's" average in 25sec range and I provided a link for reference. Regards, Wes.

http://milkyway.cs.rpi.edu/milkyway/results.php?userid=1017038&offset=0&show_names=0&state=4&appid=
ID: 61811 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
Profile mikey
Avatar

Send message
Joined: 8 May 09
Posts: 3315
Credit: 519,768,907
RAC: 28,126
Message 61814 - Posted: 1 Jun 2014, 10:45:08 UTC - in response to Message 61811.  

Happy to see a new benchmark started, since I had to replace the card used in the previous test because one of the two fans seized. So I replaced the 7950 TOP with an R9 280X TOP (ASUS). It has a factory OC of 1070Mhz and 1600Mhz on the memory. I use the latest Boinc version and AMD graphics driver (not the beta) on Win7 64bit Pro. Run times to complete "106.88 credit WU's" average in 25sec range and I provided a link for reference. Regards, Wes.

http://milkyway.cs.rpi.edu/milkyway/results.php?userid=1017038&offset=0&show_names=0&state=4&appid=


IF you want the old card back up and running check out the Artic Cooling aftermarket cooling fans. You can take your current fans off and put new ones on.

I too am glad a new thread was started, the old one got pretty long.
ID: 61814 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
[TA]Assimilator1
Avatar

Send message
Joined: 22 Jan 11
Posts: 375
Credit: 64,657,871
RAC: 0
Message 61815 - Posted: 1 Jun 2014, 11:48:43 UTC - in response to Message 61814.  
Last modified: 1 Jun 2014, 11:56:50 UTC

Well hopefully this benchmark WU will be around for a while so this thread will end up long too ;).
Times upcoming? :)

WES
Thx for your time :). So which BOINC & driver version are you using then?
I'll add the time here when a few more have been posted.

Btw, like mikey said, you could replace the fans on your old card, unless it got toasted??
Team AnandTech - SETI@H, DPAD, F@H, MW@H, A@H, LHC, POGS, R@H, Einstein@H, DHEP, WCG

Main rig - Ryzen 5 3600, MSI B450 G.Pro C. AC, RTX 3060Ti 8GB, 32GB DDR4 3200, Win 10 64bit
2nd rig - i7 4930k @4.1 GHz, HD 7870 XT 3GB(DS), 16GB DDR3 1866, Win7
ID: 61815 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
superpower

Send message
Joined: 30 Aug 10
Posts: 10
Credit: 22,660,541
RAC: 0
Message 61816 - Posted: 1 Jun 2014, 12:54:58 UTC

I have made some tests overclocking the graphic card (not on daily use).
With gpu clock 900 mhz and memory at 1200 mhz I have reached an acceptable temperature at 83°/85°C.

756905252 566189843 1 Jun 2014, 12:28:58 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 43.39 1.65 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
756905225 566189816 1 Jun 2014, 12:28:58 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 44.15 1.76 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
756905224 566189815 1 Jun 2014, 12:28:58 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 44.32 1.75 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
756896953 566182611 1 Jun 2014, 12:14:21 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 43.35 1.86 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
756896949 566183614 1 Jun 2014, 12:14:21 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 43.33 1.89 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
ID: 61816 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
WES

Send message
Joined: 22 Feb 14
Posts: 10
Credit: 198,555
RAC: 0
Message 61817 - Posted: 1 Jun 2014, 13:14:11 UTC

Hi and thanks for the info which'll make an interesting summer project as I plan on matching the 7950 TOP with an E8500 my g/son uses atm. The Boinc version is 7.2.42 and graphics driver is AMD Catalyst ver. 14-4.
ID: 61817 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
[TA]Assimilator1
Avatar

Send message
Joined: 22 Jan 11
Posts: 375
Credit: 64,657,871
RAC: 0
Message 61819 - Posted: 1 Jun 2014, 16:50:26 UTC - in response to Message 61816.  
Last modified: 1 Jun 2014, 16:55:15 UTC

Thx WES :)

I have made some tests overclocking the graphic card (not on daily use).
With gpu clock 900 mhz and memory at 1200 mhz I have reached an acceptable temperature at 83°/85°C.

756905252 566189843 1 Jun 2014, 12:28:58 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 43.39 1.65 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
756905225 566189816 1 Jun 2014, 12:28:58 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 44.15 1.76 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
756905224 566189815 1 Jun 2014, 12:28:58 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 44.32 1.75 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
756896953 566182611 1 Jun 2014, 12:14:21 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 43.35 1.86 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
756896949 566183614 1 Jun 2014, 12:14:21 UTC 1 Jun 2014, 12:43:03 UTC Completed and validated 43.33 1.89 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)

Wow! you got your 5970 to 900 MHz!? Nice :D

I've added that to the AT table, I'll add it to a table here after a couple more results. Your 5970 is now near the stock 7950 time! :)
Team AnandTech - SETI@H, DPAD, F@H, MW@H, A@H, LHC, POGS, R@H, Einstein@H, DHEP, WCG

Main rig - Ryzen 5 3600, MSI B450 G.Pro C. AC, RTX 3060Ti 8GB, 32GB DDR4 3200, Win 10 64bit
2nd rig - i7 4930k @4.1 GHz, HD 7870 XT 3GB(DS), 16GB DDR3 1866, Win7
ID: 61819 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
Arivald Ha'gel

Send message
Joined: 30 Apr 14
Posts: 67
Credit: 160,674,488
RAC: 0
Message 61821 - Posted: 2 Jun 2014, 12:25:28 UTC

Hello,

Gigabyte R9 280X Radeon Core 1100MHz Ram 950MHz.

757669598 566723026 2 Jun 2014, 12:06:41 UTC 2 Jun 2014, 12:22:21 UTC Completed and validated 24.10 1.79 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
757669596 566704044 2 Jun 2014, 12:06:41 UTC 2 Jun 2014, 12:22:21 UTC Completed and validated 24.10 1.83 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
757669594 566025361 2 Jun 2014, 12:06:41 UTC 2 Jun 2014, 12:21:14 UTC Completed and validated 24.15 1.79 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
757669583 566683478 2 Jun 2014, 12:06:41 UTC 2 Jun 2014, 12:22:21 UTC Completed and validated 24.09 1.78 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)
757669546 566745328 2 Jun 2014, 12:06:41 UTC 2 Jun 2014, 12:22:21 UTC Completed and validated 24.10 1.81 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)

Avarage easily calculated.
Sometimes 23s...
757654231 566733311 2 Jun 2014, 11:38:53 UTC 2 Jun 2014, 11:57:56 UTC Completed and validated 23.16 1.72 106.88 MilkyWay@Home v1.02 (opencl_amd_ati)

I might even try to reach 1.15GHz or 1.2GHz...
ID: 61821 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
[TA]Assimilator1
Avatar

Send message
Joined: 22 Jan 11
Posts: 375
Credit: 64,657,871
RAC: 0
Message 61823 - Posted: 2 Jun 2014, 17:40:52 UTC - in response to Message 61821.  
Last modified: 2 Jun 2014, 17:44:51 UTC

Thx for your time, & yea let us know what times you get when you've found it's best speed :).

Interesting that your GPUs time nearly matches DutchDKs 'faster' GPU!

************************************************************************************

Current GPU statistics ~ Average Run Time to Complete 1 MW v1.02 106.88 credit WU :-

R9 280X (GPU 1185 MHz, RAM 1600 MHz) .............. 23s ...... DutchDK
R9 280X (GPU 1100 MHz, RAM 950 MHz) ................ 24.1s ... Arivald Ha'gel
HD 7950 (GPU 1188 MHz, RAM 1250 MHz) .............. 24.1s ... GLeeM
R9 280X (GPU 1070 MHz, RAM 1600 MHz) .............. 25s ...... WES
HD 7950 (GPU 1000 MHz, RAM 1250 MHz) .............. 28.1s ... GLeeM
HD 7950 (GPU 900 MHz) ...................................... 33s ...... Tom*
HD 7950 (stock) .................................................. 39.8s ... Rudy Toody
HD 5970 (GPU 900 MHz, RAM 1200 MHz) ............... 43.7s ... superpower
HD 5850 (GPU 850 MHz, RAM u/c 500 MHz) ............ 51s ..... Assimilator1
HD 5970 (GPU 735 MHz, RAM 1010) ...................... 52.6s ... superpower (dual GPU card)
HD 5850 (stock) .................................................. 60s ..... Assimilator1
GTX 690 (stock) ................................................. 394s .... S@NL - JBG (dual GPU card)

Current CPU statistics ~ Average CPU Time to Complete 1 MW v1.0x 106.88 credit WU :-

Intel Xeon X5570 (Turboing to 3.2 GHz) ............... 3376s ... DutchDK

As before, the links are busted due to this forums software, go to the AnandTech thread if you want to check out the links.

I'll post my CPU times when BOINC finally gives it a few WUs!
Team AnandTech - SETI@H, DPAD, F@H, MW@H, A@H, LHC, POGS, R@H, Einstein@H, DHEP, WCG

Main rig - Ryzen 5 3600, MSI B450 G.Pro C. AC, RTX 3060Ti 8GB, 32GB DDR4 3200, Win 10 64bit
2nd rig - i7 4930k @4.1 GHz, HD 7870 XT 3GB(DS), 16GB DDR3 1866, Win7
ID: 61823 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
DutchDK

Send message
Joined: 13 Nov 10
Posts: 5
Credit: 18,929,782
RAC: 0
Message 61827 - Posted: 2 Jun 2014, 21:30:47 UTC - in response to Message 61823.  

Not so weird, since the GPU speed is close. Memory speed is not that important in the crunching of milkyway WU's.

What puzzle's me though, is the reason why Arivald is underclocking his memory. All Gigabyte's R9-280X cards run their memory at 1500 mhz (GDDR5 = 6000 Mhz), if you look at the Gigabyte site.
I think Arivald is mistaking the core speed (950 Mhz, boost to 1100), which his card has, as mem/core speeds.

It would help if Arivald posted his actual card model number, since currently Gigabyte has 2 versions of their R9-280X standard cards, and 2 versions of their R9-280X Overclock edition cards, and 1 version of their R9-280 (non-X) cards:

http://www.gigabyte.us/products/product-page.aspx?pid=4913#sp
http://www.gigabyte.us/products/product-page.aspx?pid=4914#sp
http://www.gigabyte.us/products/product-page.aspx?pid=4793#sp
http://www.gigabyte.us/products/product-page.aspx?pid=4845#sp
http://www.gigabyte.us/products/product-page.aspx?pid=4991#sp

ID: 61827 · Rating: 0 · rate: Rate + / Rate - Report as offensive     Reply Quote
1 · 2 · 3 · 4 . . . 19 · Next

Message boards : Number crunching : New Benchmark Thread - times wanted for any hardware, CPU or GPU, old or new!

©2024 Astroinformatics Group